How to use Morning Vibe

Don’t worry, it’s simple.

FAQs can be found at the bottom of the page

If you run into any issues or have any questions, please don’t hesitate to reach out on our socials, found by clicking the below icons. We genuinely care about our customers, so we closely monitor our socials for customer queries.

Set-up and How to, Made Easy

Absolutely any issues or queries then please do not hesitate to reach out through the contact methods found by clicking the above social icons.

Set-up

Please charge to 100% before first use to achieve approx. 1 month battery life.

Remove the unit from the strap and plug in to any USB-A port; plug adaptors, computers/laptops, TVs or games consoles.

Note: it fits into USB ports both ways (horizontal orientations) but only charges one way. You will know it's charging as it lights up and vibrates, flip horizontally if needed. For the best performance, keep the battery above 30%.

Controls

There is only 1 button; you can either quickly press or hold down.

Presses are for cycling i.e. through screens (current time, battery % and your 10 alarms) or numbers and ON/OF whilst editing. Holding is to begin and end editing.

Navigation

(From standby (blank screen))

  • 1 quick press - Time Screen (this will automatically then show date if left untouched)

  • 2 quick presses - Battery Percentage Screen

  • 3 - 12 quick presses - All 10 of your customisable alarm screens (all by default 00:00 and inactive) Note: Screen will revert to standby after a couple seconds of no presses.

Current Time/Date/Year/Format Set-Up

Hold the button on the current time screen (1st screen) to begin editing it. The time will flash and allow you to cycle through the hours of the day with repeated presses. Hold again to confirm once correct hour is chosen. It will then allow you to edit and confirm minutes just the same.

Next, the edit and confirm date (month first then day), year and finally 24 or 12 hour clock. For ease of set up, it is recommended you remain on 24 hour.

Note: please ensure the time and date are correctly set up or else any alarms you set may not trigger at the intended time/day.

Alarm Editing/Set-Up

From any of your 10 individual alarm screens (presses 3 - 12) you can set new alarms / edit existing ones by holding the button.

Set alarm time as above with the current time set up - press button to cycle through hours, hold to confirm, then repeat for minutes.

You will then be able to cycle between ON and OFF and confirming for each day of the week, sequentially. Monday to Sunday are represented by numbers 1 to 7.

Stopwatch Set-Up

From the battery percentage screen hold the button until you see 00:00. Press once to start, press again to disable. Once disabled, wait a few seconds to exit.

You are now an expert. Its time to start your day off buzzing!

As mentioned, please do not hesitate to reach out and we will give you our 100% attention!

 FAQs

  • Please double check it is charged by removing the unit from the strap and plugging into any USB-A plug/device. You will know the device is charging as it will light-up and vibrate. Note: please ensure you have plugged it in the correct way around. It can plug into devices in both orientations - if you see no lights or vibrations just simply plug it in the other way around.

  • Hold the button for 30 seconds until it flashes and vibrate. Please remember that all alarm data will be lost when doing this but current time/date will remain.

  • No, we would advise against wearing your device in the shower as it has no official IP rating.

  • If your Morning Vibe does not activate when you would expect i.e. you set an alarm for a certain time and it does not go off; there is likely an issue with set up.

    Reason 1 is that the current time and date may not be set up correctly, on the first screen. Your Morning Vibe needs the correct current time to activate your alarms correctly.

    Reason 2 is there is an issue with the alarm set up itself. Please remember that the days of the week are reflected by 1 - 7, representing Monday - Sunday. If you would like an alarm to activate on a given day, set that day (number) to ON during set up. If you do not want it to activate on that day set it to OF.

  • You may have an alarm enabled that you are unaware of or current time may be incorrect. Please check through all of your ten alarms 1 by 1 and deactivate. Alternatively, you can factory reset to start from scratch as described as above.

  • Please ensure that the device is charged sufficiently. Keep it above 30% for peak performance.

  • When a pre-set alarm goes off, your device should vibrate for 60 seconds then stop. At any point during this you can press the power button to stop it early. If the device continues to vibrate passed 60 seconds please factory reset by holding the power button for 60 seconds.

  • Yes! Once you set an alarm(s) it will continue to go off daily for as long as you keep them active. Unless you factory reset your device.